联系我们

保定晟诺输送机械制造有限公司

手机:13673127077

联系人:李经理

邮箱:snjx666@126.com

地址:河北保定蠡县工业区

新闻动态
皮带输送机托辊的使用与维护
皮带输送机托辊的使用与维护
Use and maintenance of belt conveyor idler
一、皮带输送机托辊的使用与维护
I. use and maintenance of idlers for belt conveyors
1、托辊使用前应仔细检查外观有无严重磕碰受损现象,旋转托辊应转动灵活,无卡阻。
1. Carefully check the appearance of the roller before use if there is any serious knock-and-tear phenomenon. The rotary roller should be flexible to rotate, without jamming.
2、托辊的安装距离应视物流的种类和输送机特点运量大小经科学计算而定,避免过疏或过密安装。
2. The installation distance of the roller should be decided by the type of logistics and the transport capacity of the conveyor, so as to avoid over-sparse or over-close installation.
3、托辊安装应适应避免相互间磨碰。
3, idler installation should be adapted to avoid grinding and bumping.
二、皮带输送机托辊的维护
Two. Maintenance of belt conveyor idlers
1、托辊正常使用寿命20000h以上,一般不需维修。但根据使用场所和负荷的大小,应制定相应的维修日期,及时清洗注油维修,及时清理浮煤。对有异常声响和不转的托辊要及时更换。
1. The normal service life of idlers is above 20000h. However, according to the size of the use site and load, thezengyab.75ix.com huagongb.75ix.com nongjiangb.75ix.comzhujiangb.75ix.com mifengj.75ix.commifeng.75ix.com  corresponding maintenance date should be established, timely cleaning and oil injection maintenance, timely cleaning of floating coal. The roller with abnormal sound and no rotation should be replaced in time.
2、更换轴承时,必须使轴承保持架口向外,轴承装入托辊后,应保持适当的游隙,不得压死。
2. When replacing bearings, the bearing cage must be made outward. After the bearing is loaded into the roller, proper clearance should be maintained and the bearing must not be pressed to death.
3、迷宫密封件应采用原厂配件,装配时应分别装入托辊内,不得套在一起装配。
3. The labyrinth seals shall be fitted with the original factory parts. They shall be respectively loaded into the roller during assembly, and shall not be assembled together.
4、使用过程中托辊应严防重物击砸托辊管体。
4, during the use of the idler, we should prevent heavy objects from smashing the idler tube.
5、为确保托辊密封性能及使用性能,禁止随意拆卸托辊。
5, in order to ensure the sealing performance and performance of the roller, it is forbidden to dismantle the idler at will.

联系方式

  1. 保定晟诺输送机械制造有限公司
  2. 手机:13673127077
  3. 联系人:李经理
  4. 邮箱:snjx666@126.com
  5. 地址:河北保定蠡县工业区

版权 © 保定晟诺输送机械制造有限公司 网址:http://tuogunw.75ix.com  推荐:橡胶托辊,槽型托辊,皮带托辊,平行托辊

冀ICP备14022170号 友链:邢台空调维修 上海空压机 上海电动伸缩门 保定打标机 精密铸造 NSK轴承总代理 网站建设及优化保定遨游网络公司